Q How can I tell if a TV has a 10-bit panel to process the full 10-bit color of high dynamic range (HDR) video? I’ve heard that certain TVs accept 10-bit signals, but display them at 8-bit resolution. I’m interested in buying Samsung’s 2016 KS9810 SUHD TV, a top-of-the-line model from 2016, but want to make sure it has 10-bit display. How will I be able to tell the difference?—Jerry Peterson
Q I’m looking to buy a new AV receiver. Denon just came out with the AVR-S930H, a 7.2-channel model that’s Dolby Vision compatible. Should I instead buy a 2016 model with similar features minus the Dolby Vision support? It would save me a few hundred dollars. The only Ultra HD source I plan to use it with is a Roku player. —Steve Guminy
A Here’s a question that has probably been asked and answered a thousand times. I plan to upgrade my system from a 7.1-channel to a 7.1.4 Dolby Atmos configuration. Should I replace my current dipole surround speakers with direct-radiating speakers? Also, which 11.2-channel AV receivers should I consider buying? —Dave Brown / via e-mail
I recently bought a 7.1-channel receiver, along with a 5.1 speaker system. Due to space limitations, I plan to install the surround speakers in the rear of room behind the seating area. Here’s my question: Should I configure the rear speakers in my receiver’s setup menu as Surrounds or Back Surrounds? —Greg Smith
Q I don’t even know what to call it, but I'm looking for a reasonably priced device ($150 or less) with enough watts to drive a small pair of two-way speakers that’s also internet-enabled and capable of playing back Pandora, Spotify, and iTunes (not Apple Music) tracks from my iPhone. Can you make a recommendation? —Scott Oakley, Pine, AZ
A A recent firmware update for my Onkyo receiver added Dolby Atmos processing, but the receiver only accommodates two height speakers. Is it worth cutting into my ceiling for such a minimal setup? If so, where should the speakers be positioned? —Peter Noris / via e-mail
Q I received an el-cheapo Victrola Vintage turntable for Father’s Day. Bypassing the built-in speakers, I eagerly connected the turntable’s RCA outputs to an auxiliary input on my Denon AVR X4200W receiver and played “Bohemian Rhapsody” from Queen’s Greatest Hits. I expected to be greeted by the warm, crackly sound of vinyl playing through my GoldenEar Technology Aon 3s (with help from a 12-inch JL Audio E-Sub), but instead heard a shrill, disappointing mess that lacked low-end and had virtually no stereo image. Comparing the vinyl to a Hi-Res digital recording I own of the same track, the vinyl sounded more like AM radio. Here’s my question: is vinyl all hype, or am I the victim of a low-end turntable? —Chris Wilson, Alpharetta, GA
A If I use two Dolby Atmos-enabled towers as the front left/right speakers in my system, will that be sufficient to experience the format when playing discs with Atmos soundtracks? — David Lambert / via e-mail
Q I’m having trouble getting a picture from my cable box when running it through a HDCP 2.2-compliant AV receiver. I’m thinking that the problem might be the cable modem/router attached to my system, which is more than 10 years old. Is there such a thing as a HDCP 2.2-compliant cable modem/router, or could the problem lie elsewhere? —Bill Ferguson
Q In the early days of high-res audio, I downloaded loads of music from HDtracks and played it on my laptop with JRiver Media Center. More recently, I took the plunge on a Premium subscription from music streaming service Tidal.
Here’s my question: Which has better sound quality, music downloaded from HDtracks or streamed from Tidal? I did listening comparisons using the same songs from each service but couldn’t tell a difference. (HDtracks downloads had slightly better clarity, perhaps?) I’m also wondering if one service offers higher resolution than the other. —Timothy Hatfield
A I’m using a Yamaha AX-497 integrated amplifier to power a pair of Elac speakers with a nominal 4-ohm impedance. I also have a Yamaha YST-SW315 subwoofer I’d like to use in my system. Here’s my question: If the speakers are wired directly to the amp as speaker pair A, and the powered subwoofer is connected as speaker pair B, can I power both simultaneously without damaging the amplifier? (The amplifier’s manual warns against connecting more than one pair of 4-ohm speakers.) For convenience reasons, I would rather not wire the main speakers through the subwoofer. —V.A. Dare / via e-mail
Q There’s been much discussion about MQA technology and its capabilities, but the only products that support MQA are a handful of DACs and stereo amps.
When can we expect to see MQA in mainstream AVRs such as those from Marantz, Yamaha, Denon, Pioneer, and Onkyo? For me, there’s no point in upgrading to a new receiver now if MQA decoding can’t at least be added via a firmware update. —Jacek G.
A I own an Integra DTR-40.6 AV receiver that is capable of playing Hi-Resolution Audio (HRA). Here’s what I want to know: If I were to upgrade my Pandora or Spotify account to stream HRA, would I be able to listen to it using the Pandora or Spotify app built into the receiver? My internet service plan is 50-Mbps FIOS, and I have the receiver connected to my router with an Ethernet cable. &Tony Held / via e-mail
Q I own an Audio-Technica AT-LP120-USB turntable that I’ve modded. I’ve also purchased a Cambridge Audio CP1 phono preamp to connect the Audio-Technica to my Denon AVR-X6200W receiver. Can you help me understand how to hook the CP1 up to the Denon? I’ve tried many options but still fail to get sound. The turntable plays when plugged into another amp so I know it’s working correctly —Rodger Benson
Q I’m interested in reconfiguring my speaker setup for object-based audio. Should I leave the surround back speakers in place, or set them up as height speakers? —Michael Welters